b'Shoulder Cryo/CuffPatient InformationICPatient: Doctor:What is the Cryo/Cuff IC?The Aircast Cryo/Cuff IC (Intermittent Compression) is an integratedTo re-fill cooler:approach to cold therapy that combines cold and focal compressionWhen ice has melted, unplugto better manage pain and reduce swelling. Intermittent cold and focalthe cooler.compression are delivered using a motorized delivery system.IMPORTANT: EMPTy the Cryo/Cuff How is the Cryo/Cuff IC used? COMPlETEly while still attached to the cooler.STep 1 - Before applying the Cryo/Cuff, prepare the cooler (Figure 1) When Cryo/Cuff is empty then empty the cooler. Repeat steps 1-5 in STep 1 1.Connect the blue tube to cooler. to prepare the cooler for refilling.2.Add cold water to line inside cooler. To clean cooler:3.Fill with ice.4. Lay insulation disk on top of ice. Attach cooler lid snugly.Use mild detergent to clean cooler and 5.Allow five minutes with occasional shaking to chill water.lid. DO NOT submerge lid under water.STep 2 - Always apply empTy Shoulder Cryo/Cuff (Figure 2) Figure 1. To troubleshoot: (The first time, have another person help) 1.Make sure unit has ice and water Use only Aircast CryoCuffs and ArcticFlow Cuffs with Aircast filled to the line indicated inside Cryo/Cuff IC Unit. the cooler. Snugly secure strap around torso in front and back. Adjust underam2.Check power connections at strap (first time only). Secure front and back elastic straps. wall and at the unit.Carefully and completely read instructions supplied with the3.Make sure to fill Cryo/Cuff prior specific Cryo/Cuff prior to application. Please follow the to operating unit as instructions instructions below to continue cooler preparation. indicate.STep 3 - Fill and pressurize Cryo/Cuff (Figure 3) Figure 2. 4. Check Cryo/Cuff connection; make sure to listen for a click To fill cuff-connect blue tube to Cryo/Cuff. Raise cooler nowhen connecting the hose to more than 15 (38 cm) above the cuff for approximately the Cryo/Cuff.30 seconds while Cryo/Cuff fills.5.Make sure unit and Cryo/Cuff are To correctly position cooler-place cooler on stable surface.level for optimal performance.The cooler base should be even with the Cryo/Cuff NOTE: To AVOID excessive pressure during use, DO NOT raise6.This device may be susceptible the cooler higher than 15 (38 cm) above the Cryo/Cuff. to magnetic or electromagnetic To turn cooler on-plug power supply into wall outletinterference. If this occurs, and connect cord to lid. relocate or reposition the device.7.Increase the separation Figure 3.between the equipment.! CAUTION 8.Plug the power supply into anDO NOT use an elastic wrap with the Cryo/Cuff IC. outlet on a circuit different thanDressings used under the Cryo/Cuff should be applied lightly. other devices. When filling the Cryo/Cuff IC, DO NOT raise the cooler higher than 15 (38 cm)9.If unit motor is still not functioning above the Cryo/Cuff avoid excessive pressure. unit can be used as a gravity Reduce pressure with any sense of discomfort, numbness or tingling of the limb. fed device (see Figure 3) EMPTy the Cryo/Cuff after each use, and prior to refilling. for positioning.Patient skin condition checks must occur every 1 2 hours on a routine basis.FOR pRODUCT SUppORT CALL1-888-405-3251DJO, LLC.1430 Decision Street, Vista, CA 92081-8553 U.S.A.Phone 760.727.1280Toll Free 800.526.8785Fax 800.457.4221 2010 DJO, LLC. Cryo/Cuff is a trademark of DJO, LLC. 00-0868 Rev B aircast.com'